Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
We've stumbled upon this post relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the net and believe it made perfect sense to write about it with you in this article.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old tub is readily available, the job can relocate easily; if you need to open up a wall to remove the old tub and position the new tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have actually currently gotten a new tub and don't require to transform the plan of your previous water system pipes.
Your tools and material list must make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub till the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as additionally examine the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait till the tub has been made use of at the very least once as this will certainly resolve it into its final placement.
Getting ready for the Installation
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, triggering the water to permeate the wall between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been brought to that write-up on How to Install a Bathtub Yourself from someone on a different domain. Do you know someone else who is very much interested in the topic? Be sure share it. Thank you for going through it.
Schedule Now!
Report this page